Consider the following scenario:

• On a Windows Vista-based computer, you try to print a document to an XML Paper Specification (.xps) print queue.
  Note: The document does not have to be an .xps document.
• The computer is put into standby.

In this scenario, after you resume the computer from standby, the print job is removed from the print queue, and the document does not print.

Consider the following scenario:

• You use some embedded USB devices on a computer that is running the Windows Vista operating system.
• You put the system into standby.
• You resume the computer from standby.

In this scenario, you may receive a Stop error that resembles the following:

STOP 0×000000FE ( parameter1, parameter2, parameter3, parameter4)

Notes:

• Standby is also known as sleep mode or S3 mode.
• The four parameters in the Stop error message vary depending on the configuration of the computer.
• Not all “Stop 0×000000FE” error messages are caused by this problem.

Consider the following scenario:

• You are running a Windows Vista-based portable computer from a docking station.
• The computer has a USB device connected to it.
• You put the computer into standby (S3).
• You resume the computer from standby.

In this scenario, a yellow exclamation mark (!) may appear next to the USB device in Device Manager. This problem may occur if the status of the docked portable computer is changed when the system is in standby.

The information in this article applies to the following configuration(s):

• Quake 3
• Quake 4
• Radeonâ„¢ HD 2400 series
• Windows Vista 32-bit Edition
• Windows Vista 64-bit Edition
• Windows XP Professional
• Windows XP Home Edition
• Windows XP Media Center Edition
• Windows XP Professional x64 Edition

Symptoms:
Quake 3 and 4: Resuming from a standby state results in the display image appearing too bright

The information in this article applies to the following configuration(s):

• Catalyst Control Center
• Radeonâ„¢ X1950 series
• Radeonâ„¢ X1900 series
• Radeonâ„¢ X1800 series
• Radeonâ„¢ X1650 series
• Radeonâ„¢ X1600 series
• Radeonâ„¢ X1550 series
• Radeonâ„¢ X1300 series
• Radeonâ„¢ X1050 series
• Radeonâ„¢ X850 series
• Radeonâ„¢ X800 series
• Radeonâ„¢ X700 series
• Radeonâ„¢ X600 series
• Radeonâ„¢ X550 series
• Radeonâ„¢ X300 series
• Radeonâ„¢ 9800 series
• Radeonâ„¢ 9700 series
• Radeonâ„¢ 9650 series
• Radeonâ„¢ 9600 series
• Radeonâ„¢ 9550 series
• Radeonâ„¢ 9500 series
• Windows Vista 64-bit Edition

Symptoms:

On a dual display configured system, after returning from sleep mode, the secondary display may not be enabled.

The information in this article applies to the following configuration(s):

• Radeon Xpress 1100
• Radeon Xpress 1150
• Windows Vista 32bit Edition
• Windows Vista 64bit Edition

Symptoms:
A flickering display may be noticed when playing a DVD using the Windows Media Player in full screen and resuming from a standby state after disconnecting a CRT display device.

The information in this article applies to the following configuration(s):

• Catalyst Control Center
• Catalyst Display Driver 6.11
• ATI Radeon Xpress 200 Series
• Windows Vista

Symptoms:
After disconnecting the primary display device while Windows Vista is in standby mode, the login screen may fail to appear when resuming from standby.

When you run Windows Vista in audit mode for a long time, the computer enters standby or hibernation. By default, you are then prompted to perform an administrator logon after the computer resumes. This behavior occurs during an automated factory preinstallation operation. In this scenario, the automated factory preinstallation process is interrupted.